ECI Product Manuals. ELP Series Reverse Osmosis Systems, Open PDF. 999411, Valve Nest Stager Installation & Operation Manual, Open PDF. EcoWater Systems Acquires VRTX Technology and Operations; Expands Green Product.

• EcoWater Systems Conditioner with Remote (ECR) EcoWater Systems Refiner with Remote (ERR) SERIES 3500 & 3502 Systems Tested and Certified by NSF Interna- ERR 3500R20 & ERR 3502R30 are Tested tional and WQA against NSF/ANSI Standard and Certified by WQA against NSF/ANSI 44 for water softening performance and the Standard 42 for chlorine taste and odor. • Consult the dealer or an experienced radio/TV tech- Use care when handling the EcoWater Systems condi- nician for help.

Do not turn upside down, drop, or set on Changes or modifications not expressly approved by sharp protrusions. • Your local dealer will provide details regarding this warranty or writing within 30 days from the expiration of these guar- will refer you to the factory for additional information.

In addition, the 3500 SERIES antees upon EcoWater Systems LLC, P.O. • OTHER REQUIREMENTS STANDPIPE LAUNDRY TUB A drain is needed for recharge discharge water.

A floor drain is preferred, close to the EcoWater Systems con- FIG. Tayanie snegov pohozhie filjmi. 1B ditioner/refiner.

A laundry tub, standpipe, etc., are other options (See Figure 1B). NOTE: The Commonwealth of Massachusetts plumbing A 120V, 60 Hz, grounded, continuously “live”.

• TUBES cover, bag(s) of small parts needed to assemble and install a. If installing an EcoWater Systems Bypass Valve, put the unit, plus this manual, in the other. Lubricated o-ring seals onto both bypass valve ports (See EcoWater Systems conditioner/refiner models R20, R30 and Figure 3B). • (See Figure 4A). 3 - - Valve Bypass BYPASS INLET OUTLET VALVE VALVE VALVE nozzle & venturi EcoWater Systems Bypass Valve ground clamp o- -ring from conditioner/ brine to conditioner/ refiner elbow PULL OUT.

• Fully open two or more conditioned cold water faucets nearby the EcoWater Systems conditioner/refiner. Care is taken at the factory to keep your EcoWater Systems conditioner/refiner clean and sanitary.

However, during ship- b. Place the bypass valve(s) in bypass position (See ping, storage, installing and operating, bacteria could get into Figure 6). • SETUP PROCEDURE electronic control compensates automatically after you set the iron level in Step 11, below. When the EcoWater Systems conditioner/refiner is plugged in for the first time, a beep sounds and the dis- 8.

Press the SELECT ( ) button. • S Y S T E M S CONDITIONER/REFINER STATUS SCREENS MAIN MENU During normal operation, the EcoWater Systems condi- tioner/refiner’s display shows up to four status screens (Page 14 explains how individual screens can be turned on or off). Each is shown for six seconds, in a rolling sequence (See Figure 15). • ECOWATER Conditioner/Refiner Operation S Y S T E M S CONNECTING TO REMOTE When the conditioner/refiner’s electronic control is first powered up, it is not yet in communication with the remote. Chem otkritj fajl sii. Do the following to establish a link between FIG. 19 the two: 1.

• ECOWATER Conditioner/Refiner Operation S Y S T E M S SETTING SALT LEVEL LOW SALT ALARM Use this feature when adding salt to the conditioner/ Use this feature to program when the electronic control refiner. Will display a low salt alarm. The number of days can be customized, or the feature can be turned off. • ECOWATER Conditioner/Refiner Operation S Y S T E M S RECHARGING THE CONDITIONER/REFINER SETTING THE CURRENT TIME When the conditioner/refiner’s electronic control is first This feature may be used to assure an adequate supply of conditioned water at times of unusually high water powered up, a “wizard”. • ECOWATER Conditioner/Refiner Operation S Y S T E M S SETTING RECHARGE TIME SETTING HARDNESS When the conditioner/refiner’s electronic control is first When the conditioner/refiner’s electronic control is first powered up, the default time for starting an automatic powered up, a “wizard” screen prompts you to enter recharge is 2:00 a.m.

• ECOWATER Conditioner/Refiner Operation S Y S T E M S MODIFYING ROLLING SCREENS SETTING THE LANGUAGE During normal conditioner/refiner operation, four status When the conditioner/refiner’s electronic control is first screens are shown in sequence (See “Conditioner/ powered up, a “wizard” screen prompts you to set the Refiner Status Screens”. • ECOWATER Conditioner/Refiner Operation S Y S T E M S SETTING TIME FORMAT SETTING HARDNESS UNITS Use this feature to select a 12-hour (AM/PM) or 24-hour Use this feature to select grains or parts per million clock. (ppm) as hardness units. • ECOWATER Conditioner/Refiner Operation S Y S T E M S SYSTEM INFORMATION Use these features to look up the following information about the conditioner/refiner and its operations: Model information (model number and software version) FIG. 51 Water available (conditioned water ready for use) Daily average water used Water used today Total water used (explained in Step 6, below) • ECOWATER Conditioner/Refiner Operation S Y S T E M S CYCLE TIMES 8a. Backwash time: Press the UP ( ) or DOWN Use these features to change the following conditioner/ ( ) buttons to change the backwash time. Refiner operations: Hold the button down to rapidly advance.